Title: How to make Arjac Stonefist
shorty - October 26, 2009 11:49 AM (GMT)
This is a Guide how you could make one of the new character heads of the Space Wolves Army Logan Grimnars personal Champion...the One with the fliing Thunder Hammer aka Thor....a guide how to build Alric Stonefist:
You may need the following parts:
-Terminator (Black Reach or you also could take a Space Wolf Terminator, if you use Black Reach you need to drill out the Terminator helmet so you could implant a Space Wolf head)
-Terminator Storm Hammer Arm (best will be one from the Space Wolf Terminator Box best looking is the Hero One with the real sculptured Wolf Head on the End)
-Terminator Stormshield Arm and Shield (same here best will be the Space Wolf Terminator Box again I used the Shield with the Wolf Head)
-Terminator Storm Hammer Head (from the Space Wolf Terminator Box or the normal Close Combat Terminator because you only need the Head, here i used the one with the Runes and the encraved Wolfhead End)
-Some Leftover Sprue Part to build Anvil Middle (you can use every leftover Sprue, i turned it so that the bigger side is facing up looking more like a forging anvil plate)
-Smaller flat Sprue Part to make the Envil upper Side (for that Pyramid forging plate look)
- Powerarmor Frontpart with the Wolftooth and Rune on it (on the new Space Wolf Sprue or the older Greyhunter Sprue from the Mailorder, carve of only the front Wolftooth chain from the body without damaging it too much, then you have a normal Space Wolf Powerarmor front leftover)
- one Head from the new Space Wolf Sprue or the Space Wolf Terminator Sprue (I found out that the Head from a Longfang One (no hair looking like he has two big Earphones on) will be the best head for Arjac.
- Wolfpelt (selfmade from greenstuff or using the one from the Space Wolf Terminator box or Greyhunter Upgrade Sprue (the wolfpelt on the back Powerarmor cut so that you only have the pelt)
- two leftover Terminator Shoulderguards (you can use the plain ones, i did it and used the wolfskull on the left shoulder to have a replacement for the Terminator Honours)....
You should findout the rest for yourself. I was amazed how that Black Reach Termie looked after the transformation *ggg*...sorry no Pic right now...but maybe you have one if you build your Arjac and share your Pic and maybe how you build that new Character model.
Kidjal - October 26, 2009 01:36 PM (GMT)
A shopping list of materials from mostly the same boxset, under the title guide, with no guide?
I don't doubt those parts could be used to do that but with a "guide" you would expect...well, a guide.
Rogal Dorn - October 26, 2009 05:34 PM (GMT)
i made mine from a Captain Lysander model, shaving off the first symbols, greenstuffing fur and runes, making a beard, and sticking a dwarf banner anvil on top of his head
Bullvine - February 28, 2010 07:06 PM (GMT)
I'm made mine from the space wolves plastic Terminators boxed
Feytor - February 28, 2010 07:42 PM (GMT)
Looks very nice, but you could make him a long beard, oh and take better pic next time, this one looks blury.
Bullvine - March 1, 2010 10:00 PM (GMT)
I've added better pic's ;)
Rogal Dorn - March 2, 2010 01:06 AM (GMT)
heres my Arjac
i shaved off all the IMperial FIst logos from Captain Lysander, greenstuffed over the shield to make it flat. Sculpted a beard on him, and glued the anvil to his head. Then i greenstuffed fur over the cloak.
Vredesbyrd - May 4, 2010 03:55 PM (GMT)
Slight necro, but with a valid question so its all groovy.
Where did you guys get the anvil from that you've used on Arjac? My guess is the Warmaster Anvil of Doom but I'm not entirely sure.
fritzagelmann - May 4, 2010 05:07 PM (GMT)
battle for skull pass dwarf standard bearer
Vredesbyrd - May 4, 2010 08:43 PM (GMT)
Bullvine - May 5, 2010 11:14 AM (GMT)
I got mine from the standard top in the Dwarf warrior boxed set.
Rogal Dorn - May 5, 2010 01:03 PM (GMT)
same here, dwarf warrior banner